Modem Technicolor TC7200 (for Fixed Internet Cable)
The modem is used to connect to the internet if you have cable internet from Vodafone (exUPC internet).
Technical Specifications:
- Cable modem EURO DOCSIS® 3.0 WIFI EMTA.
- 4x Ethernet 10/100/1000 with traffic signaling (4 RJ-45 connectors for Internet access), 2x RJ-11 for telephone, 1x coaxial cable connector.
- Wireless Wi-Fi connection in 2.4 GHz (IEEE 802.11b/g/n) and 5 GHz (IEEE 802.11b/g/n) versions - switchable. The modem has internal Wi-Fi antennas. The Internet connection speed depends on the ordered tariff and local conditions and differs from the maximum speed of the home Wi-Fi network, the modem supports speed tariffs up to 300 Mbit/s.
- The dimensions of the modem are 220 x 166.7 x 43 mm.
- Supply voltage: 230 V (AC), maximum power consumption: 18 W, average power consumption: 8.7 W, AC/DC adapter: ADAPTER 18 W, 12 V, DC/1.5 A. Average consumption is 8.7 W.
Downloads:
- User guide (in Czech only).
- Declaration of Conformity (version v2) (in Czech only).
You might find useful:
What do the lights on the modem mean?
Power
- On - the cable modem is on.
DS
- Blinking - downstream channel scanning.
- On - downstream channel tuned, standard operating state.
US
- Blinking - upstream channel scanning.
- On - upstream channel tuned, standard operating state.
Online
- Blinking - network connection scan.
- Lights up - the startup process is complete, the modem is connected to the network, standard operating status.
Ethernet 1-4
- Blinks or lights up - signaling sending/receiving data from the device behind the modem, standard operating status.
- Not lit - the port is not occupied, the connected device is turned off.
USB (for service purposes only)
- Blinks or lights up - signaling sending/receiving data from the device behind the modem.
Wireless - Link
- Lights up - the wireless part is active, without data transmission.
- Blinks - signaling sending/receiving data from the device behind the modem via Wi-Fi, standard operating state.
- It does not light up - the wireless part is turned off.
TEL1/TEL2
- Blinks - registration of the EMTA telephone part on the telephone switchboard.
- Lights up - active line, modem is registered on the telephone exchange.
- It does not light up - there is no telephone service indicated in the modem.
How do I get into the modem's administration and change my login information?
- Log in to the Wi-Fi network of the modem or connect over a data cable and enter the address http://192.168.0.1 in the browser. If you are using your own Wi-Fi router and in the modem mode section you have selected modem mode (bridge), the address for entering the administration is http://192.168.100.1 .
- You need a username and password to access the administration, the default login and password is admin for both values. After logging in for the first time, you can change your password to your own for your own safety. You can make the change in the administration in the menu System – Password.
How do I turn on Wi-Fi, how can I change the name and password or the 2.4 GHz / 5 GHz frequency?
By default, the Wi-Fi network is turned on, the name of your network (SSID) and password (Wi-Fi Password) can be found on the label on the modem. We have also prepared for you general information on the operation of Wi-Fi networks.
Log in to the modem administration.
Connect to the modem via Wi-Fi or a data cable and enter the address http://192.168.0.1 in the browser. To log in, use the username admin and the password you set, or the default password (admin).
Go to the menu Wireless - Radio.
Choose whether you want to turn on Wi-Fi at a frequency of 2.4 GHz or 5 GHz and in the Radio section enable Wi-Fi network broadcasting. In the same section, you can edit the name of your Wi-Fi network. You can then change the password in the Security section. Always remember to save your changes.
The Technicolor TC7200 modem allows you to set up a more modern 5 GHz Wi-Fi transmission band, which you can use especially in places where the normal 2.4GHz wireless network shows very low speed or frequent outages caused by the presence of a larger number of Wi-Fi networks in your vicinity or you require higher requirements for stability and connection speed. However, keep in mind that not every device can work with Wi-Fi at the 5 GHz frequency and that the Wi-Fi network in this band has a shorter range. Wi-Fi at 5 GHz has a different name and password, you can also find this data on the label located on the base of the modem, to read it you need to turn the modem upside down. If you switch the modem to 5 GHz Wi-Fi and find that none of your devices support it and you cannot log into the modem menu, perform a factory reset of the modem. Insert, for example, a pen into the RESET button on its back panel and hold for approximately 30 seconds until the modem flashes. After that, wait about 5 minutes, the modem will have its original settings restored.
How do I change the Wi-Fi channel in case of Wi-Fi interference?
Before changing the settings, read the detailed information about the Wi-Fi channels.
Log in to the modem administration.
Connect to the modem via Wi-Fi or a data cable and enter the address http://192.168.0.1 in the browser. To log in, use the username admin and the password you set, or the default password (admin).
Go to the menu Wireless - Radio.
Choose the right type of Wi-Fi network (2.4 GHz or 5 GHz) and in the Radio - Channel section you can select a new broadcasting channel from the roller shutter. Don't forget to save the settings.
How do I switch the modem to bridge mode?
Switching the modem to bridge mode is especially useful in cases where you want to connect your own router behind the modem or you need to ensure the correct assignment of a fixed IP address to your own device. Your home devices (mobile phones, laptops and others) will then connect to the network created by your own router, which you connect behind the modem. Bridge mode is only available if you have an IP address from us in IPv4 format. If you are currently using IPv6, please contact us to arrange a change. After setting the bridge mode, the default address for modem administration will be changed to http://192.168.100.1 .
Log in to the modem administration.
Connect to the modem via Wi-Fi or a data cable and enter the address http://192.168.0.1 in the browser. To log in, use the username admin and the password you set, or the default password (admin).
Go to the menu System - Change settings and set the Bypassed settings here.
Select the Bypassed settings option in the drop-down menu and save the settings.
Mějte přehled o svých službách díky aplikaci Můj Vodafone
